Button

Button

This page describes the configuration options available for the MOSH button element, including how to define its properties and map them to virtual wires.

The button element reads a digital GPIO pin and reports press, release, and advanced input events such as long press, double press, and short-long combinations.

Creating a Button element

#include <mosh_core.h>
#include <elements/button.h>
 
MOSH_Core MOSH_Core;
 
const uint8_t pin = 4
MOSH_Element_Button* myButton = nullptr;
 
void setup() {
  myButton.monitor(pin);
  MOSH_Core.registerElement(myButton);
}

Parameter Table:

Option	Type	Default	Description
active_low	bool	false	Whether active state is low (true for inverted logic)
debounce_delay	uint8_t	50	Amount of delay (in milliseconds) used for debouncing
id	integer	–	Unique Element ID
long_press_delay	uint16_t	750	Amount of delay (in milliseconds) for determining a long press
name	string	–	Friendly label
pin	uint8_t	–	GPIO pin number connected to the button
press_delay	uint16_t	250	Amount of delay (in milliseconds) for determining a short press
pullup	bool	true	Enable internal pull-up resistor
stream_on_press	bool	false	Sends a stream of PRESS notifications when the button is active
stream_on_press_freq	uint16_t	50	The amount of time between PRESS notifications when stream_on_press is true
virtual_wire	uint8_t	–	ID of the virtual wire is assigned
constant_on	bool	false

Property Status Messages:

enum class MOSH_Element_Button_Status

Name	Bit	Description
RESET	0x00	Reserved for future use.
STATE_ON	0x01	Sent when the button is placed in the “pressed” position.
STATE_OFF	0x02	Sent when the button is released
PRESS	0x03	Sent when the button is pressed and released within the press_delay
DOUBLE_PRESS	0x04	Sent when the button is pressed and release twice within the press_delay
LONG_PRESS	0x05	Sent after the button is released after being pressed for long_press_delay
SHORT_LONG_PRESS	0x06	Sent after a combination of a PRESS and LONG_PRESS
USER_DEF1	0xFC	Sent with button_element.send_userdef_1()
USER_DEF2	0xFD	Sent with button_element.send_userdef_2()
USER_DEF3	0xFE	Sent with button_element.send_userdef_3()
USER_DEF4	0xFF	Sent with button_element.send_userdef_4()

Static config:

None

Setup Methods:

Methods intended to be called during setup or initialization. These configure how the element behaves and are typically not changed during runtime.

Method	Direction	Required	Default	Parameters	Description
setActiveLow(bool)	Write	❌	true	bool	Button is pressed when pulled low
setDebounce(uint16_t)	Write	❌	10	uint16_t	Set the debounce time in milliseconds
setLongPressDelay(uint16_t)	Write	❌	750	uint16_t	Set the long-press delay in milliseconds
setName(string)	Write	❌	null	string	Set a friendly name for the element
setPin(uint8_t)	Write	✅	null	uint8_t	The pin the button is wired to
setPressDelay(uint16_t)	Write	❌	250	uint16_t	Set the press delay in milliseconds
setPullup(bool)	Write	❌	true	bool	Use the internal pullup
setStreamOnPress(bool)	Write	❌	false	bool	Button will send stream of PRESS events while active
setStreamOnPressFreq(uint16_t)	Write	❌	null	uint16_t	Sets how frequently a PRESS event is sent during a press stream

Runtime Methods:

Method	Direction	Parameters	returns	Description
buttonIsPressed()	Read	–	bool	Returns true if button is pressed, false if not
getFriendlyName()	Read	–	string	Returns the friendly name of the element
getLastPropertyChange()	Read	–	uint32_t	get the amount of time (in millies) since the last state change)
getProperty(name)	Read	friendlyName, state, event, lastChange	PropertyValue	Returns the current value of a property
getID()	Read	–	uint8_t	Returns the element's unique ID
getName()	Read	–	String	Returns the element's friendly name.
send_userdef_1()	User called	–	void	User defined action
send_userdef_2()	User called	–	void	User defined action
send_userdef_3()	User called	–	void	User defined action
send_userdef_4()	User called	–	void	User defined action

Table of Contents